enterasys switch configuration guide

Procedure 5-4 Configuring Management Authentication Notification MIB Settings Step Task Command(s) 1. macauthentication port Enables or disables MAC authentication on a port Disabled. You can do this by doing the following: Connect the switch to PuTTY with a 9-pin serial cable. Display MAC authentication configuration or status of active sessions. When tunnel mode is configured, VLAN-to-policy mapping will not occur on a stackable fixed switch or standalone fixed switch platform. This guarantees that the default behavior of a bridge is to not be part of an MST region. Figure 25-1 Basic IPv6 Over IPv4 Tunnel Router R1 Router R2 VLAN 20 195.167.20.1 Tunnel 10 IPv6 Addr: 2001:DB8:111:1::20/127 Tunnel Source: 195.167.20.1 Tunnel Destination: 192.168.10.1 VLAN 10 192.168.10.1 Tunnel 10 IPv6 Addr: 2001:DB8:111:1::10/127 Tunnel Source: 192.168.10.1 Tunnel Destination: 195.167.20. Strict Priority Queuing With Strict Priority Queuing, a higher priority queue must be empty before a lower priority queue can transmit any packets. Configuring CLI Properties Basic Line Editing Commands The CLI supports EMACs-like line editing commands. Ifnointerfaceisspecified,IPv6DHCPstatisticsforallinterfacesarecleared. Port 5 looks up the destination MAC address in its FID. If the device supports routing, enter router configuration mode and configure an IP address on the VLAN interface. If the port is configured so that it is connected to a switching device known to implement Loop Protect, it uses full functional (enhanced) mode. set sflow receiver index ip ipaddr 3. sFlow Table 18-7 lists the commands to display sFlow information and statistics. show ipv6 status If necessary, enable IPv6 management. System(su)->show port ratelimit fe.1.1 Global Ratelimiting status is disabled. Table 9-1 show spantree Output Details, About GARP VLAN Registration Protocol (GVRP), Policy Classification Configuration Summary. Configuring DVMRP System(su)->router(Config-if(Vlan 1))#exit System(su)->router(Config)#interface vlan 2 System(su)->router(Config-if(Vlan 2))#ip igmp enable System(su)->router(Config-if(Vlan 2))#exit IGMP Display Commands Table 19-5 lists Layer 2 IGMP show commands for Enterasys stackable and standalone devices. Display the current timeout period for aging learned MAC entries/ show mac agetime 3. SNTP Configuration b. The following example inserts a new entry into IPv4 extended ACL 121 before entry 2. 7 Configuring System Power and PoE This chapter describes how to configure Redundant Power Supply mode on the C5 and G-Series switches, and how to configure Power over Ethernet (PoE) on platforms that support PoE. Router 2 will translate Type 7 LSAs from the connected domain to Type 5 routes into the backbone. Brand . * or ge.1.1-48) assign egress vlan: set vlan egress X ge.1.x untagged You can enable it using the set igmpsnooping adminmode command on Enterasys stackable and standalone devices as described in Configuring IGMP on page 19-15. Implementao e Suporte em Redes convergentes de Voz e Dados para suporte de toda a Soluo SIEMENS proposta, com estudo de novas tecnologias que se adequam necessidade de novos . For a subnet with the address 192.168.12.0/24, the directed broadcast address would be 192.168.12.255. Link Aggregation Control Protocol (LACP) is described in Chapter 11, Configuring Link Aggregation. Setting target parameters to control the formatting of SNMP notification messages 5. Though it is possible to configure policy from the CLI, CLI policy configuration in even a small network can be prohibitively complex from an operational point of view. A dependent downstream device on a pruned branch restarts. Stateless autoconfiguration is part of Router Advertisement and the Enterasys Fixed Switches can support both stateless and stateful autoconfiguration of end nodes. Connects a PC to the network providing internet only access to the network. Understanding How VLANs Operate Preparing for VLAN Configuration A little forethought and planning is essential to a successful VLAN implementation. When console-only access is configured, all TCP SYN packets and UDP packets are dropped, with the exception of UDP packets sent to the DHCP Server or DHCP Client ports. The terminology associated with CoS configuration is introduced in Table 17-1. Port Configuration Overview Auto-Negotiation and Advertised Ability Auto-negotiation is an Ethernet feature that facilitates the selection of port speed, duplex, and flow control between the two members of a link, by first sharing these capabilities and then selecting the fastest transmission mode that both ends of the link support. Implementing VLANs building has its own internal network. Configuring IPv4 ACLs Procedure 24-1 describes how to configure IPv4 standard and extended ACLs. 2. Setting the value to 0 will set the timeout to forever. Spanning Tree Basics that port will be selected as root. Ports assigned to a new port group cannot belong to another non-default port group entry and must be comprised of the same port type as defined by the port group you are associating it with. This information is used to determine the module port type for port group. In the shared LAN example it may take over as designated port if the original designated port is disabled. It assumes that you have gathered the necessary TACACS+ server information, such as the servers IP address, the TCP port to use, shared secret, the authorization service name, and access level attribute-value pairs. 19 Configuring Multicast This chapter describes the multicast features supported by the Enterasys fixed switches. (For example: security or traffic broadcast containment). C5(rw)->set linkflap portstate disable ge.1.1-12 Link Flap Detection Display Commands Table 8-3 lists link flap detection show commands. Policy Configuration Overview Applying a Default Policy The following example assigns a default policy with index 100 to all user ports (ge.1.1 through ge.1.22) on a switch: System(su)-> set policy port ge.1.1-22 100 Applying Policies Dynamically Dynamic policy assignment requires that users authenticate through a RADIUS server. Configuring PIM-SM R1(su)->router(Config)#interface vlan 3 R1(su)->router(Config-if(Vlan 3))#ip address 172.1.2.1 255.255.255.0 R1(su)->router(Config-if(Vlan 3))#ip igmp enable R1(su)->router(Config-if(Vlan 3))#ip ospf enable R1(su)->router(Config-if(Vlan 3))#ip pimsm enable R1(su)->router(Config-if(Vlan 3))#no shutdown R1(su)->router(Config-if(Vlan 3))#exit R1(su)->router(Config)#interface vlan 4 R1(su)->router(Config-if(Vlan 4))#ip address 172.1.3.1 255.255.255. If LAG members with different port speeds should tie for the lowest port priority, the LAG member with the lowest port number breaks the tie. Table 15-8 Commands for Monitoring MSTP Task Command Verify that MSTP is running on the device. When bridges are added to or removed from the network, root election takes place and port roles are recalculated. Creating and enabling VLANs. Using Multicast in Your Network Figure 19-4 PIM Traffic Flow 7 3 1 DR RP Source 5 4 2 6 Last Hop Router Receiver 1. Active Cisco 800 Series Router Configuration. The CIST contains a root bridge, which is the root of the Spanning Tree for the network. 3. Be sure that your serial connection is set properly: Baud rate: 115200 bps (for 5420, 5520, X435, X465, X590, X690, X695, and X870 models) Baud rate: 9600 bps (for other models) Data bits: 8 Stop bit: 1 Parity: none Flow control: none set linkflap threshold port-string threshold_value 5. Configuring OSPF Areas Example Figure 22-5 OSPF NSSA Topology Area 1 RIP Backbone Router 1 Router 2 Router 3 Router 4 Router 5 Using the topology shown in Figure 22-5, the following code examples will configure Router 2 as the ABR between Area 1 and the backbone area 0. Refer to the CLI Reference for your platform for command details. User Authentication Overview Figure 10-3 Selecting Authentication Method When Multiple Methods are Validated SMAC=User 1 SMAC=User 2 SMAC=User 3 Switch MultiAuth Sessions Auth. Use the clear port broadcast command to return broadcast threshold settings to the default of 14881 packets per second. Refer to Licensing Advanced Features on page 4-8 for more information. set port discard port-string {tagged | untagged | none | both} 8. Assign to queue assign the packet to a queue Note: Unlike other Fixed Switch platforms, A4 ACLs are not terminated with an implicit deny all rule. Refer to page Power over Ethernet Overview Pan/Tilt/Zoom (PTZ) IP surveillance cameras Devices that support Wireless Application Protocol (WAP) such as wireless access points Ethernet implementations employ differential signals over twisted pair cables. The MST region presents itself to the rest of the network as a single device, which simplifies administration. VRRP is available only on those fixed switch platforms that support advanced routing and on which an advanced feature license has been enabled. Use the dir command to display the contents of the images directory. ThisexampleshowshowtodisplayPWAinformationforge.2.1: portstring (Optional)DisplaysPWAinformationforspecificport(s). ExtremeXOS User Guide Version 22.7 > STP > Spanning Tree Protocol Overview > Compatibility Between IEEE 802.1D-1998 and IEEE 802.1D-2004 STP Bridges > Bridge Priority > Spanning Tree Protocol . engine ID A value used by both the SNMPv3 sender and receiver to propagate inform notifications. Configuring SNMP . Configuration of normal port mirroring source ports and one destination port on all switches, as described above. installation and programing guide and user manuals. Understanding and Configuring Loop Protect Communicating port non-forwarding status through traps and syslog messages Disabling a port based on frequency of failure events Port Modes and Event Triggers Ports work in two Loop Protect operational modes. RADIUS looks up the user account for that user based upon the SMAC. You can also use the show commands described in Reviewing and Enabling Spanning Tree on page 15-20 to review information related to all Spanning Tree protocol activity. sFlow sFlow Agent Functionality Packet flow sampling and counter sampling are performed by sFlow Instances associated with individual Data Sources within the sFlow Agent. UsethiscommandtodisplaythecontentsoftheNeighborCache. Using Multicast in Your Network Generation ID gen id: 1331801871 10.5.40.0/255.255.255.0 [2] via neighbor: 10.5.50.1 Uptime: 66704 , expires: 0 version: 3 Generation ID gen id: 1331805217 10.5.50.0/255.255.255.0 [0] via neighbor: direct 10.5.51.0/255.255.255.0 [0] via neighbor: direct direct direct Uptime: 3615 , expires: 0 version: 3 10.5.70.0/255.255.255.0 [3] via neighbor: Uptime: 66716 , expires: 0 version: 3 10.5.60.0/255.255.255. How RADIUS Data Is Used The Enterasys switch bases its decision to open the port and apply a policy or close the port based on the RADIUS message, the port's default policy, and unauthenticated behavior configuration. C5(su)->router(Config)#show access-lists 120 Extended IP access list 120 1: deny ip 20.0.0.1 0.0.255.255 any 2: deny ip 30.0.0.1 0.0.255.255 any 3: deny ip 40.0.0.1 0.0.255.255 any 4: permit ip any any C5(su)->router(Config)#no access-list 120 2 3 C5(su)->router(Config)#show access-lists 120 Extended IP access list 120 1: deny ip 20.0.0.1 0.0.255. Configuration Examples Enabling a Server and Console Logging Procedure 14-1 shows how you would complete a basic Syslog configuration. If a DHCP relay agent or local DHCP server co-exist with the DHCP snooping feature, DHCP client messages will be sent to the DHCP relay agent or local DHCP server to process further. By default, all applications running on the Enterasys switch are allowed to forward Syslog messages generated at severity levels 6 through 1. See The RADIUS Filter-ID on page 8 for RADIUS Filter-ID information. 4. The allocation mechanism attempts to maximize aggregation, subject to management controls. Functions and Features Supported on Enterasys Devices Disabling Spanning Tree Spanning Tree may be disabled globally or on a per port basis. Port auto-negotiation Enabled on all ports. GVRP must be enabled to allow creation of dynamic VLANs. Disable Telnet inbound while leaving Telnet outbound enabled, and show the current state. Stops any pending grafts awaiting acknowledgments. Procedure 12-2 SNMPv3 Configuration Step Task Command(s) 1. Save Your System Configuration Settings. As soon as a rule is matched, processing of the access list stops. 3. Up to 5 TACACS+ servers can be configured, with the index value of 1 having the highest priority. For example: A4(su)->show boot system Current system image to boot: a4-series_06.61.00.0026 Use the set boot system command to set the firmware image to be loaded at startup. Use the passive-interface command in router configuration command mode to configure an interface as passive or to set passive as the default mode of operation for all interfaces. Switch Configuration Using CLI Commands Guidelines for Rackmount Installation Attaching Brackets and Installing in Rack About SecureStack Switch Operation in a Stack 44 Recommended Procedures to Install New and Existing Stacks Installing a New Stackable System of Up to Eight Switches Adding a New Switch to an Existing Stack Important

Parma Senior High Alumni Association, Surfboard Art Australia, Articles E